Used Mazak INTEGREX for Sale
The Mazak INTEGREX is Yamazaki Mazak’s multi-tasking series: a turning spindle with C-axis, topped by a full milling spindle on a swiveling B-axis plus a Y-axis — turning and simultaneous 5-axis milling in a single setup. If you’re looking for a used Mazak INTEGREX, TÖRNER has traded 61 machines of this series and currently has 9 in stock (as of July 2026), from the 200-IV ST to the i-350 HS. Every machine is fully inspected and documented by our own technicians; we handle worldwide shipping and installation ourselves, and financing is arranged through our partners. TÖRNER is an independent dealer and is not affiliated with Yamazaki Mazak Corporation.
Mazak INTEGREX Machines at Törner
The INTEGREX Series Explained
Milling Spindle on a Swiveling B-Axis
What separates an INTEGREX from a turning center with live tooling is the milling spindle: it sits not in the turret but on a swiveling B-axis above the main turning spindle, driven backlash-free through a roller gear cam and indexed in 0.0001° increments. Combined with the Y-axis, that delivers true simultaneous 5-axis machining rather than just radial and axial drilling patterns.
- Swivel range — depends on the model; for the INTEGREX i-150, Mazak quotes -10° to 190°
- i / i-H generations — Y-axis is standard; for the i-H series, Mazak quotes 210 to 300 mm of travel depending on machine size
- Older series — Y-axis was an option, identifiable by the model suffix: 100Y, 300Y or 200 SY
Model Suffixes: S, T, ST and H
The letters after the model number describe the configuration. For purchasing, this is the decision that matters most: an i-200S can finish a part on the second spindle, an i-200 without the S cannot. Equally defining for the series is the tool magazine with automatic tool changer — capacity varies considerably within the same model designation, so it belongs in every inquiry.
- S — second turning spindle; both turning spindles are C-axis controlled and can be synchronized for part transfer
- T — lower turret
- ST — second spindle and lower turret combined
- H — the newer i-H generation with its flat machine front
- Tool holder & spindle interface — like magazine capacity, we confirm both from the datasheet of the specific machine
Mazatrol Control Generations
When buying used, the control determines day-to-day usability and the programming environment. Every generation handles EIA/ISO G-code from your CAM system alongside Mazatrol conversational programming. Matching control to build year is only a rough guide, though: overlaps and non-standard configurations do occur.
- MAZATROL Fusion 640MT — fitted, for example, to the 200 SY in our stock
- Fusion 640MT Pro — 200-III T/ST and 300-III
- MAZATROL Matrix and Matrix 2 / Nexus — Generation IV, e-1060 V II, i-200S
- SmoothX — introduced by Mazak in 2014 with SMOOTH TECHNOLOGY
- SmoothAi — the current control on the i-H, i-V, e-H and e-V
Formats From Lathe-Like to Vertical
The machine format should match your part geometry. The core 100/200/300/400 series and the i and i-H series follow a lathe-like layout, size increasing with the number — Mazak quotes a 6-inch chuck on the i-100, 8 inches on the i-200 and 10 inches on the i-350. Simultaneous 5-axis capability is something we verify case by case. QUICK TURN, HYPER QUADREX and VARIAXIS have no turning spindle with second spindle and lower turret like the INTEGREX.
- e-H — large horizontal mill-turn center for long, heavy shaft work
- e-V — double-column 5-axis machine with rotary table
- i-V — vertical 5-axis machining center with pallet changer
- j series / j NEO — B-axis in 5° steps per Mazak (1° optional); j NEO indexes in 1° as standard, optionally 0.0001°
- QUICK TURN / HYPER QUADREX — milling runs through live tooling in the turret
- VARIAXIS — primarily 5-axis machining centers where only the T variants turn via a rotary table
61 machines
Traded by TÖRNER
9 machines (July 2026)
Currently in stock
640MT to SmoothAi
MAZATROL control generations
C-axis turning spindle + B/Y milling spindle
Kinematics
Machines sold
Everything about your Mazak INTEGREX
Whether it’s purchase, transport, maintenance, or financing — we accompany you through the entire process. Our technicians know Mazak machines inside and out.
We buy your Mazak INTEGREX
We buy your used Mazak INTEGREX fairly and quickly.
Maintenance & repair
Certified technicians for Fanuc controls and Mazak-specific components.
Transport & commissioning
Professional dismantling, transport and commissioning including customer training.
Financing & leasing
Flexible financing options for your Mazak machine purchase — including hire purchase.
Mazak INTEGREX machine request
Looking for a specific model of the series? We'll find it for you.
Other model series
We also trade these Mazak series — and any other on request.
The series at a glance
TÖRNER’s stock covers the series across several generations. Currently available are an INTEGREX i-350 HS and an i-100 H from the i-H generation with its flat machine front, plus an i-300, an i-200S, an i-150 and an i-100 from the i-Series, two INTEGREX 200-IV ST from the Matrix generation, and a 200 SY paired with a Mazak GL100C gantry loader as a ready-to-run automation cell (as of July 2026). Over the years, INTEGREX machines from every core line have passed through our hands — from the 100 to 400 series of generations II through IV, through the i-Series, up to the large e-H and e-V formats. Your choice should therefore hinge less on the model number than on chuck size, distance between centers, second spindle, tool capacity and control generation.
Frequently asked questions about the Mazak INTEGREX
What condition are the used INTEGREX machines in, and how is that verified?
Every machine is inspected and documented by our own technicians before sale — the condition of the main and milling spindles, guideways, B-axis, tool changer and control, operating hours where they can be read out, plus the accessories and tooling included. On an INTEGREX, the B-axis and second spindle deserve particular scrutiny, because the accuracy of done-in-one machining depends on them. An inspection under power can be arranged by appointment.
What warranty do I get when buying a used machine?
We sell B2B, and the scope of liability for defects is expressly set out in the purchase contract — so you see it before signing, not after delivery. Up front you receive the condition report and inspection documentation, with an under-power inspection on request. We agree commitments on function at handover, commissioning and rework individually for each machine — raise them before ordering so they go into the quote in writing.
Which Mazatrol control is fitted, and what does that mean for programming?
That depends on the build year: older INTEGREX machines run MAZATROL Fusion 640MT or 640MT Pro, Generation IV runs Matrix or Matrix 2, and newer machines run SmoothX or SmoothAi. Which control and software level is actually installed is something we verify machine by machine and state in the quote — going by build year alone is not reliable. Every generation processes G-code from your CAM system alongside Mazatrol conversational programming.
Do you handle shipping, installation and commissioning?
Yes. We organize dismantling, transport, installation and commissioning as one end-to-end service, including operator training on request. TÖRNER ships worldwide — export documentation and sea-freight packaging for overseas shipments are part of the service. Plan foundation and utility requirements as well as crane and access dimensions early: ST variants with a bar feeder or gantry loader need considerably more floor space than the bare machine footprint.
What if the model I'm looking for isn't in stock right now?
Then we take over the search. Through a worldwide network of dealers and end users, we place your machine request with your key specs — series, chuck size, distance between centers, second spindle, control and build-year window. As soon as a suitable INTEGREX becomes available, we get back to you with the datasheet and a technical assessment. No need to trawl the listings yourself.
Are financing and trade-in of my existing machine possible?
Leasing and hire purchase are arranged through our financing partners; terms and durations come directly from the partner and depend on creditworthiness, machine age and investment volume. Buying your existing machines, on the other hand, is something we do ourselves — including as part of a changeover, where one INTEGREX replaces a previously two-stage turning and milling process. Send us details of the machines you're letting go — type, build year and control — and we'll appraise them and credit the value against your purchase.
Find the Right INTEGREX
Give us a call or send us a quick outline of your workpiece through the form — diameter, length and whether you need a second spindle is enough to get started. Everything else, from tool capacity and distance between centers to the Mazatrol generation your team knows, we’ll sort out on the phone. You’ll receive the datasheet, photos and condition report for matching machines from our stock; if the model you’re after isn’t currently available, we’ll launch a machine search through our worldwide network. TÖRNER is an independent dealer of used machine tools and is not affiliated with Yamazaki Mazak Corporation. Mazak, INTEGREX and MAZATROL are trademarks of Yamazaki Mazak Corporation and are used here solely to describe the machines offered.